How To Install A Backup Camera On A F250 Super Duty To The Factory To The Radio

A solid, high-quality backup camera is an essential investment to heighten your confidence and safety while reversing a vehicle. This is especially important in large vehicles or trucks with trailers or equipment, which tin can exist difficult to maneuver and create bullheaded spots. A fill-in camera is a simple solution that is easy to install yourself to eliminate blind spots and help you maneuver with ease and conviction, instead of straining your neck and risking dents and dings. Just not every fill-in camera installation is a straightforward one, such as instances where the tailgate of a truck is removed to accommodate equipment and hauling needs.

This was the case of one man driving a 2019 Ford F-250 equipped with a tailgate salt spreader. The salt spreader is large enough to block the driver's rear view, while also extending from the dorsum of the truck. This made it challenging to safely back the truck out of driveways, in parking lots, and down streets. A fill-in photographic camera was the obvious solution, but virtually backup cameras are installed on a truck's tailgate. The tailgate was removed from the bed to accommodate the spreader, leaving few options for locations to install the backup camera.

So, how do y'all install a fill-in camera on a truck without a tailgate? Thanks to Camera Source, backup cameras are not only easy to install yourself, they are easy to customize to adapt your unique needs. Continue reading to find out how to install an OEM backup camera on Ford SuperDuty with the tailgate removed, and watch the video posted by DS Trucks

Getting Started

Every Camera Source backup photographic camera installation kit comes with easy step by step instructions for DIY installation. Since the truck owner in the video doesn't accept a tailgate to install the backup camera on, they got creative and installed the photographic camera directly on the salt spreader. We'll summarize how they did it and compare and dissimilarity what they did with the typical installation procedure, forth with tips on other ways to customize and improvise.

Required Tools

Phillips head screwdriver
Tape measure
Drill
14mm or 9/sixteen" drill flake
File for deburring
Rubbing alcohol

Included in the kit

Photographic camera bezel
Camera (CS-FTRSK-17SDRC)
Wire Harness
4 housing screws
2 self tapping installation screws

Step ane. Place the Center of the Vehicle

You want to install the camera at the center of the vehicle for the all-time viewing bending. On a Ford SuperDuty, that's commonly around 48 inches high. You will run across in the video that they adamant the centre elevation by recognizing where the backup photographic camera was positioned on the tailgate before information technology was removed. For their purposes with the salt spreader, they preferred the viewing angle when the camera was positioned at a tiptop of 58 inches.

Modifying the height of the camera makes a big difference considering it can requite you a smaller or wider field of vision. You will discover in the video, the installer wasn't able to see the end of the common salt spreader, but they had a longer range of view of the surface area behind them. At this height, they were comfortable with the level of visibility of the surface area behind the truck and of the table salt spreader to monitor it.

Stride 2. Clean the Surface & Adhere the Camera

Clean the surface where you're going to be installing and mounting the camera so the adhesive will stick while securing it with screws. Retrieve you're going to need to drill nine/xvi" holes in the surface you're attaching the backup camera to.

One of the prissy features of Photographic camera Source backup cameras is that the enclosures include agglutinative strips to help determine the ideal placement and agree the photographic camera in place until it is secured with screws. Since this truck was already equipped with a backup camera and monitor, they were hands able to connect the camera and check the field of vision for adjustments before attaching it with screws.

Footstep 3. Wiring & Attaching the Camera

Ordinarily when you install a backup photographic camera, you lot drill into the surface of the vehicle to run the wiring through the interior to the power source under the spare tire or under the bumper. In the video, since they can't run the wire through the salt spreader, they fabricated a slight alteration to the camera housing to accommodate for this. They drilled a small hole on the side to let the wire to exit the housing and forth the exterior.

Then they secured the wiring with tape along the exterior and bundled the excess wiring with a rubber ring to preclude information technology from hanging downwards and snagging. From in that location, the wire could exist run through the holes for the previous camera and plugged in.

In one case the camera is positioned where you like information technology, screw the camera in place within the enclosure, and screw the enclosure to the surface.

Backup Camera Solutions

Y'all may notice in the video, that some backup photographic camera systems are designed to allow for multiple cameras for multiple viewing angles. This is especially helpful in situations where a driver needs to exist able to run across behind the equipment they are operating, also equally the equipment itself to make sure it's properly operating. Multiple cameras are also helpful for hitching trailers to trucks and bankroll trailers up with ease. Whatsoever the case, maximizing your range of vision is e'er great for safety and convenience. Browse our selection of backup cameras. If you're looking for unique backup camera installation solutions, browse our expansive selection of cameras , beginning exploring our resource , or contact us for a custom society if you tin can't detect what y'all're looking for.

Source: https://camerasource.com/blog/superduty-oem-rear-camera-installation-rear-camera-solution-when-tailgate-is-removed/

Posted by: hodgesnount1981.blogspot.com